Dee-zee DZ508515 Bedienungsanleitung PDF herunterladen (Seite 3)

GRILLE GUARD

2014 GMC SIERRA 1500

EXCLUDES DENALI

Page 2 of 8 9-25-13(DP)

2. Start installation from under the front of the vehicle. Determine if the vehicle is equipped with tow hooks.

Tow Hook equipped vehicles:

a. Remove the factory tow hook from the end of each frame channel, (Figure 1). NOTE: The driver

side tow hook removal and the reinstallation of both tow hooks with the Grille Guard is difficult and

assistance is highly recommended.

i. Option 1: Remove the hex bolts securing the driver side of the bumper to the bracket. Use

a short pry bar or large screwdriver to move the tab on the bumper bracket up and away

only enough to clear the hex bolt and slide it out past the bumper bracket, (Figures 2A, 2B

& 5).

ii. Option 2: Remove plastic radiator grille. Loosen and/or completely remove the front

bumper to remove the long hex bolts through the tow hooks, (Figure 2B).

b. Reattach the bumper after the tow hooks have been removed, (Figure 5). Leave factory hardware

loose at this time.

c. Next, select (1) Frame Bracket and the driver side Mounting Bracket, (Figure 9). Bolt the Mounting

Bracket to the bottom of the Frame Bracket with (3) 8mm x 25mm Hex Bolts, (3) 8mm Lock

Washers and (3) 8mm Flat Washers, (Figure 10). Do not fully tighten hardware at this time.

d. Insert the Bracket assembly through the opening in the plastic bumper, (Figure 5). Line up the (3)

holes in the Frame Bracket with the holes in the end of the frame channel.

e. Insert the driver side tow hook back into position in the end of the frame above the Bracket

Assembly, (Figure 10). Reattach the tow hook using only the long factory hex bolt inserted through

the Frame Bracket and tow hook at this time. Loosen and reattach bumper as required to reinstall

the long bolt. If tow hooks are not going to be reinstalled, skip ahead to Step d, "Vehicles without

tow hooks" installation instructions.

f. Leave hardware loose at this time.

g. Repeat Steps c - f to install the passenger side Bracket assembly and tow hook. Once both

Bracket assemblies have been installed, skip forward to Step 3.

Vehicles without tow hooks:

a. Cut out the lower portion of the indented area in both sides of the plastic bumper insert to clear the

Brackets as pictured, (Figures 3 & 4). IMPORTANT: Make several small cuts for best fit. NOTE:

The plastic panel is held in place with several small screws. The screws at the top corners are

difficult to impossible to reach and remove with the bumper in place without damaging the cover. If

you prefer to remove the panel to cut out the openings, it may be necessary or easier to remove

the plastic grille then the steel bumper assembly with the plastic panel attached to access all of the

small screws and clips.

b. Reattach the bumper and/or bumper insert and grille, (if removed), once openings have been cut

out and checked for clearance, (Figure 4). Tighten all factory bumper hardware only at this time.

c. Select (1) Frame Bracket, (Figure 6). Insert the Bracket through the opening in the plastic bumper,

(Figures 4 & 5). Line up the (3) holes in the Bracket with the holes in the end of the frame channel.

d. Select (1) 12mm Double Bolt Plate, (Figure 7A). Insert the Bolt Plate into the end of the frame

channel, through the (2) holes in the side of the frame and out through the Bracket. Secure the

Double Bolt Plate to the Bracket with (2) 12mm Flat Washers, (2) 12mm Lock Washers and (2)

12mm Hex Nuts, (Figure 7B). Snug but do not fully tighten hardware at this time. Repeat this Step

to install the 12mm x 35mm Single Bolt Plate, (Figure 8A), into the remaining hole in the other side

of the frame channel and Bracket, (Figures 8B & 8C).

e. Next, select the driver side Grille Guard Mounting Bracket. Bolt the Mounting Bracket to the bottom

of the Frame Bracket with (3) 8mm x 30mm Hex Bolts, (3) 8mm Lock Washers and (3) 8mm Flat

Washers, (Figures 9 & 10). Do not tighten hardware at this time.

f. Repeat Steps c - e to install the passenger side Frame and Mounting Brackets.

3. With assistance, hold the Grille Guard up in position on the outside of the Mounting Brackets. Bolt the

Grille Guard to the Brackets with (4) 10mm x 30mm Hex Bolts, (8) 10mm Flat Washers, (4) 10mm Lock

Washers and (4) 10mm Hex Nuts, (Figure 10). Snug but do not tighten hardware at this time.

4. Check the Grille guard side to side alignment with the vehicle. Adjust as required then tighten only the (6)

8mm Hex Bolts securing the Mounting Brackets to the bottom of the Frame Brackets.

1 2 3 4 5 6 7 8 9

Kommentare zu diesen Handbüchern

Keine Kommentare

Dee-zee DZ508515 Bedienungsanleitung Seite 3

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Dee-zee DZ508515